@database doc/VMMTools.guide
@Node Main "VMM/doc/VMMTools.guide"
@Next "VMMUsage"
The following tools are available for use with VMM:
  @{"  VMMUsage       " Link "VMMUsage"}
  @{"  VMMUsageCLI    " Link "VMMUsageCLI"}
  @{"  VMMStat        " Link "VMMStat"}
  @{"  ReadMMUConfig  " Link "ReadMMUConfig"}
  @{"  ConvVMMCfg     " Link "ConvVMMCfg"}
  @{"  ShowPageSize   " Link "ShowPageSize"}
@EndNode
@Node "VMMUsage" "VMM/doc/VMMTools.guide/VMMUsage"
@Prev "Main"
@Next "VMMUsageCLI"
@Toc "Main"
VMMUsage
VMMUsage  opens a window to display the name of those tasks which have
currently  allocated  any  virtual memory.  This only works if VMM has
been configured to enable 'memory tracking'.  If you change the status
of this option old entries will remain in the list.
VMMUsage also displays the amount of virtual memory used by each task.
The slider gadget determines the update interval for this information.
@EndNode
@Node "VMMUsageCLI" "VMM/doc/VMMTools.guide/VMMUsageCLI"
@Prev "VMMUsage"
@Next "VMMStat"
@Toc "Main"
VMMUsageCLI
VMMUsageCLI does the same as @{"VMMUsage" Link "VMMUsage"} except that it does not open
a window but displays it to the console a single time.
@EndNode
@Node "VMMStat" "VMM/doc/VMMTools.guide/VMMStat"
@Prev "VMMUsageCLI"
@Next "ReadMMUConfig"
@Toc "Main"
VMMStat
VMMStat prints the statistics parameters of VMM to the console once.
@EndNode
@Node "ReadMMUConfig" "VMM/doc/VMMTools.guide/ReadMMUConfig"
@Prev "VMMStat"
@Next "ConvVMMCfg"
@Toc "Main"
ReadMMUConfig
This  tool is used only if you have difficulties in getting VMM to run
on  your  system.  You should NOT run this if VMM works perfectly.  If
you  do  so  anyway,  you have to delete the generated files from your
ENV:   and  ENVARC:   drawers  in  order  not  to  waste memory for an
unnecessary MMU table.
Running  it will take between 10 seconds and 1 minute.  It then writes
a  file  called  'VMM_MMU.config'  to ENV:  and ENVARC:.  This file is
read  by  VMM  upon startup to correctly initialize its MMU table.  If
you specify 'VERBOSE' as an option it will also print this information
in  a  more readable form to the console.  See the 'MMU setup' section
for further details.
Specifying  the 'DEBUG' option will print the page descriptor of every
logical  page.   This results in a huge amount of data and is probably
only  of  use  for  debugging  problems  in conjunction with VMM's MMU
setup.
If  the VMM_MMU.config file is used by VMM there are some
things which do not work as usual as there are:
- Enforcer  does  not work, i.e. it can be installed but it never will
  report any hits.
- The 'FAST ROM' option is ignored. You can circumvent this by running
  ReadMMUConfig with CPU FastROM running.
- The  'Cache Zorro II RAM' option is ignored. It is not needed if you 
  use ReadMMUConfig.
@EndNode
@Node "ConvVMMCfg" "VMM/doc/VMMTools.guide/ConvVMMCfg"
@Prev "ReadMMUConfig"
@Next "ShowPageSize"
@Toc "Main"
ConvVMMCfg
This  tool  can  be  used  to  convert  an  old  style  (pre-3.0)  VMM
configuration  file  to  the  new  format.   It  reads 'VMM.prefs' and
replaces  it  with  the  new style configuration file.  Normally it is
automatically called during the installation process.
@EndNode
@Node "ShowPageSize" "VMM/doc/VMMTools.guide/ShowPageSize"
@Prev "ConvVMMCfg"
@Toc "Main"
ShowPageSize
ShowPageSize  is  only used during the installation process.  It reads
the current MMU configuration and returns the possible pagesizes.
@EndNode